My MRC Pro

[Everett]

I picked this up last week brand new. It came with the servo Losi C-Hubs, Losi Zero Ackerman Knuckles Aluminum hexes and the rear bent links. I picked up a Brood Anarchy motor for it and last night I got a Tekin B1R esc for it. The guy I got the Brood from didn't know what turn it is : So I'm just going to have to try different pinions to figure out what works best. Here is my parts listing so far and how much I've spent.


~MRC Pro w/upgrades (New) = $120
~Brood Anarchy (New) = $45
~Tekin B1R (Used) = $20
~Servo (Used) = $0 (Came with the car)


~~~Total = $185 (so Far)~~~


I got the B1R for a pretty good deal off of eBay. All these prices are including shipping. I'm planning on getting Thunder Power 325mah 2s batteries to run in this. I'm going to be using my DX2S to control it and SR3520 RX. I painted up the body yesterday. It's only my 3rd body ever to paint. I didn't to terrible but the CF didn't turn out perfect. It was my first time doing CF.


Some of the Upgrades I plan on getting in the future are:


~Bodiless Chassis (Not sure which one yet)
~C.I. Lil'Nova Foams
~HB Rovers
~Gmade 13mm offset Wheel Wideners
~BWD Servo Mount/Battery Guard
~MIP CVDs
~RichardGarret's Knuckle Weights
~VP LH Procomp Wheels
~Better Servo
~BWD Motor Plate (Out of Stock)
~Chaotic Crawler Ti Links
~Losi Aluminum Rear Lockouts


These are in order of when I'm planning one getting them. LMK what other Upgrades you think would be Good for it.

[Everett]

​OK so a little update I got my B1r and got it wired up. I plugged in a battery to test all the functions and I found out I have a problem when I turn it on the wheels just start spinning and I have to push reverse to get it out of reverse. What should I do? I've tried adjusting the EPA, the Throttle Trim, and the Exponential, but it still won't fix it.

I ordered up a Thunder Power 325mah 2s 65c battery for it and that should be here Thursday or Friday. Once that comes I will have all my electronics

[Positronic]

nice, the pro is looking good, sounds like you just need to calibrate the esc

[Everett]

I've tried calibrating it but it still does it.

[Everett]

OK So I was emailing Tekin yesterday and I thought I got it worked out but when i turn it off and then turn it back on I have to calibrate it all over again.......Sooo the B1R is enroute to Tekin right now .

On a good side though I got my battery today I got a Thunder Power 325mah 65c 2s. I could have had it running if the ESC was working

[Everett]

Ok so I need to post an update so here it is...

Ok so I've done some work on it recently . Got the wideners mounted up and put on the BWD Servo Mount/Battery Guard. I had to grind down my steering link to get it to work but now it works great! I also got my shock outboard kit today and got that mounted up. Got my B1r back from Tekin and got it all wired up and I'm having lots of fun with it. I also got a BWD Motor Plate and Motor spacer for it.











I also made an indoor course for it.

[Everett]

And pics of the Motor Plate all mounted up.

[Positronic]

that's a pretty cool battery guard, nice course you have there

[Everett]

Ya I took some video today and I plugged in the memory card to load it and it wouldn't show up.

[Everett]

And I got all back in the car .

[Everett]

Update! Got a Bodiless chassis for it

[Everett]

Look what came today . My Mini-T springs came too I'm going to use the soft ones on the front and the medium ones on the rear.

[Everett]

And I have it running